Modelling the effect of material properties and process parameters on tow impregnation in out-of-autoclave prepregsCENTEA, T; HUBERT, P.Composites. Part A, Applied science and manufacturing. 2012, Vol 43, Num 9, pp 1505-1513, issn 1359-835X, 9 p.Article

Flexural strength of metakaolin ferrocementYERRAMALA, Amarnath; RAMACHANDURDU, C; BHASKAR DESAI, V et al.Composites. Part B, Engineering. 2013, Vol 55, pp 176-183, issn 1359-8368, 8 p.Article

A developed method for producing in situ TiC/Al composites by using quick preheating treatment and ultrasonic vibrationZHIWEI LIU; QINGYOU HAN; JIANGUO LI et al.Composites. Part B, Engineering. 2012, Vol 43, Num 5, pp 2429-2433, issn 1359-8368, 5 p.Article

Pore size control and electrochemical capacitor behavior of chemically activated polyacrylonitrile - Carbon nanotube composite filmsJAGANNATHAN, Sudhakar; TAO LIU; KUMAR, Satish et al.Composites science and technology. 2010, Vol 70, Num 4, pp 593-598, issn 0266-3538, 6 p.Article

Microstructures and improved wear resistance of 3D needled C/SiC composites with graphite fillerYANZHI CAI; SHANGWU FAN; HEYI LIU et al.Composites science and technology. 2009, Vol 69, Num 14, pp 2447-2453, issn 0266-3538, 7 p.Article

High-temperature mechanical properties of porous NaMgF₃ derived from directionally solidified NaMgF₃-NaF eutecticsRAMIREZ-RICO, J; DE ARELLANO-LOPEZ, A. R; MARINEZ-FEMANDEZ, J et al.Journal of the European Ceramic Society. 2008, Vol 28, Num 13, pp 2451-2457, issn 0955-2219, 7 p.Article

Study of the mechanical properties of carbon nanofiber reinforced carbon/carbon compositesJINSONG LI; RUIYING LUO.Composites. Part A, Applied science and manufacturing. 2008, Vol 39, Num 11, pp 1700-1704, issn 1359-835X, 5 p.Article

Porous nanocomposites prepared from layered clay and PMMA [poly(methyl methacrylate)]TANOGLU, Metin; ERGÜN, Yelda.Composites. Part A, Applied science and manufacturing. 2007, Vol 38, Num 2, pp 318-322, issn 1359-835X, 5 p.Article

The influence of void content on the structural flexural performance of unidirectional glass fibre reinforced polypropylene compositesHAGSTRAND, P.-O; BONJOUR, F; MANSON, J.-A. E et al.Composites. Part A, Applied science and manufacturing. 2005, Vol 36, Num 5, pp 705-714, issn 1359-835X, 10 p.Article

Thermal de-consolidation of thermoplastic matrix composites. II. Migration of voids and re-consolidationMENG LU; LIN YE; MAI, Yiu-Wing et al.Composites science and technology. 2004, Vol 64, Num 2, pp 191-202, issn 0266-3538, 12 p.Article

Physical and mechanical properties of unidirectional plant fibre composites: an evaluation of the influence of porosityMADSEN, Bo; LILHOLT, Hans.Composites science and technology. 2003, Vol 63, Num 9, pp 1265-1272, issn 0266-3538, 8 p.Conference Paper

Consolidation of polymer-derived SiC matrix composites: processing and microstructureKOTANI, Masaki; INOUE, Takahiro; KOHYAMA, Akira et al.Composites science and technology. 2002, Vol 62, Num 16, pp 2179-2188, issn 0266-3538, 10 p.Article

Physico-chemical characterization of thermally treated bentoniteZIVICA, Vladimir; PALOU, Martin T.Composites. Part B, Engineering. 2014, Vol 68, pp 436-445, issn 1359-8368, 10 p.Article

Thermoplastic polymer impregnation of cellulose nanofibre networks: Morphology, mechanical and optical propertiesJONOOBI, Mehdi; AITOMÄKI, Yvonne; MATHEW, Aji P et al.Composites. Part A, Applied science and manufacturing. 2014, Vol 58, pp 30-35, issn 1359-835X, 6 p.Article

A non-local void filling model to describe its dynamics during processing thermoplastic compositesSIMACEK, Pavel; ADVANI, Suresh G; GRUBER, Mark et al.Composites. Part A, Applied science and manufacturing. 2013, Vol 46, pp 154-165, issn 1359-835X, 12 p.Article

Compressive properties of closed-cell polyvinyl chloride foams at low and high strain rates: Experimental investigation and critical review of state of the artLUONG, Dung D; PINISETTY, Dinesh; GUPTA, Nikhil et al.Composites. Part B, Engineering. 2013, Vol 44, Num 1, pp 403-416, issn 1359-8368, 14 p.Article

Cure behaviour and void development within rapidly cured out-of-autoclave compositesAGIUS, S. L; MAGNIEZ, K. J. C; FOX, B. L et al.Composites. Part B, Engineering. 2013, Vol 47, pp 230-237, issn 1359-8368, 8 p.Article

The effects of antifreeze use on physical and mechanical properties of concrete produced in cold weatherCULLU, Mustafa; ARSLAN, Metin.Composites. Part B, Engineering. 2013, Vol 50, pp 202-209, issn 1359-8368, 8 p.Article

Preparation and characterization of polycaprolactone/forsterite nanocomposite porous scaffolds designed for bone tissue regenerationDIBA, M; KHARAZIHA, M; FATHI, M. H et al.Composites science and technology. 2012, Vol 72, Num 6, pp 716-723, issn 0266-3538, 8 p.Article

Mechanical properties of porous combustion synthesized Ni₃Ti-TiC_x compositesBURKES, Douglas E; GOTTOLI, Guglielmo; MOORE, John J et al.Composites science and technology. 2006, Vol 66, Num 13, pp 1931-1940, issn 0266-3538, 10 p.Article

Micro-mechanical modeling the densification behavior of titanium metal matrix compositesKIM, T.-W; LEE, C. H.Composites. Part A, Applied science and manufacturing. 2004, Vol 35, Num 12, pp 1375-1383, issn 1359-835X, 9 p.Article

Impact-induced deformation fields in 3D cellular woven compositesBAHEI-EL-DIN, Y. A; ZIKRY, M. A; RAJENDRAN, A. M et al.Composites. Part A, Applied science and manufacturing. 2003, Vol 34, Num 8, pp 765-778, issn 1359-835X, 14 p.Article

Investigation of shearing effects on the permeability of woven fabrics and implementation into LCM simulationLOUIS, Markus; HUBER, Ulrich.Composites science and technology. 2003, Vol 63, Num 14, pp 2081-2088, issn 0266-3538, 8 p.Article

Numerical simulation of void formation in LCMBREARD, Joël; SAOUAB, Abdelghani; BOUQUET, Guy et al.Composites. Part A, Applied science and manufacturing. 2003, Vol 34, Num 6, pp 517-523, issn 1359-835X, 7 p.Conference Paper

Novel aligned hemp fibre reinforcement for structural biocomposites: Porosity, water absorption, mechanical performances and viscoelastic behaviourBAGHAEI, Behnaz; SKRIFVARS, Mikael; SALEHI, Masoud et al.Composites. Part A, Applied science and manufacturing. 2014, Vol 61, pp 1-12, issn 1359-835X, 12 p.Article